Best-in-class guitar recording starts here. AXE I/O, IKs award-winning audio interface, set a new standard for guitar-oriented recording interfaces. Now AXE I/O Solo brings the same great tone shaping, convenient features and premium sound to everyone, everywhere, in a compact and affordable 2-in / 3-out format. 2-in / 3-out USB audio interface. Amp Out with ground loop interrupter.
High-resolution, Class A mic preamp. 24-bit, 192 kHz sound quality.Wide frequency response ideal for instruments. Ultra-low noise floor for high-gain recording. Designed and made in Italy.
AXE I/O Solo offers a triple-topology instrument input designed to preserve your guitars unique character, combined with powerful tone-shaping features to adapt to any guitar or bass, and helps you coax a wider range of sounds from any instrument. AXE I/O Solo also offers IKs patent pending Z-TONE® circuit, letting you dial in impedance from 1 MOhm (sharp) down to 2.2 kOhms (bold) that interacts with your pick-ups. At the maximum impedance, youll find your sound tighter, sharper and more precise. Increase the load and the sound becomes thicker and bolder. Youll quickly find yourself using these controls to give your guitars even more sonic character with just a few minutes experimentation you can dial in a sound that fits the mix beautifully.PURE mic preamp for transparent recording. AXE I/O Solo offers a high-definition, Class A mic preamp designed for transparent and clean recording. An extended, flat frequency response captures the full tonal range of your voice or instrument without coloring the sound, and best-in-class dynamic range ensures ultra-quiet recordings. Re-amplification made easier than ever. AXE I/O Solo offers a dedicated Amp Out, a with ground-isolated design and zero-latency routing, letting you ditch expensive and confusing reamping setups.
Its simple: connect the Amp Out to your amp, then mic it up using AXE I/O Solos microphone preamp. Now you can capture a clean copy of your signal while recording and feed it back to your amp afterwards to experiment with different amp, stompbox and microphone settings without re-recording countless takes.
A truly high-end audio interface for everybody. The original AXE I/O set a high bar for sound quality.AXE I/O Solo preserves the best-in-class dynamic range, ultra-low self-noise and wide, extended frequency response essential to capturing the most accurate details of your performance, and for keeping your sound completely pure and transparent. Advanced digital control & routing. AXE I/O Solo also includes a powerful, convenient.
Application to manage inputs & outputs and assign routing & controller inputs. In the INTERFACE tab, you can view the active inputs, enable phantom power and control the ground lift to dial in the least noise for your setup. Adjust output volume, direct monitoring routing, select the sample rate and more. The CONTROLLER tab gives you control over the 2 controller inputs.
Set behavior, MIDI channel, MIDI CC #, minimum and maximum values, and more, to dial in the best settings for any application you want to control. The AXE I/O Solo Control Panel lets you keep focused on your work, instead of adjusting settings on the unit itself, for a faster, freer workflow. AD and DA Resolution: 24-bit.Sampling Rate: 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz, 176.4 kHz and 192 kHz. Host Connection: USB Type-B receptacle.
USB 2.0 (High Speed). Configuration: Electronically balanced and floating, automatically compensates level when connection is balanced or unbalanced, tip hot. Output impedance: 150 Ohms balanced, 75 Ohms unbalanced.Output Level: 0 dBFS corresponds to +13.5 dBu. Frequency response: From 1 Hz to 46 kHz within 0.5 dB (96 kHz sample rate). Dynamic Range: 113 dB(A). THD+N: -103 dB(A) at -1 dBFS.
Channels 1-2 crosstalk: 112 dB(A). Configuration: Unbalanced, floating, with selectable ground lift.Output Level: 0 dBFS corresponds to -3 dBu. Frequency response: From 20 Hz to 42 kHz within 0.5 dB (96 kHz sample rate). Dynamic Range: 106 dB(A). Output impedance: Virtually ideal source (zero Ohms) until clipping. Maximum Output level: +9 dBu into 50 Ohms load (approx 95 mW).
Frequency response: From 1 Hz to 42 kHz within 0.5 dB (96 kHz sample rate). Dynamic Range: 111 dB(A). Configuration: Multiple topology instrument preamp. Input impedance, PASSIVE mode: Variable from 1 MOhms down to 2.2 kOhms. Input impedance, ACTIVE mode: 10 kOhms.Input level, min gain: 0 dBFS is obtained with a +12.5dBu signal at the TS input. Input level, max gain: 0 dBFS is obtained with a -19 dBu signal at the TS input. Frequency response: From 6 Hz to 42 kHz within 0.5 dB (96 kHz sample rate). Dynamic Range: 117 dB(A). THD, PURE mode: 0.002 % (-1dBFS input). THD, JFET mode: 0.5 %. Configuration: Class-A discrete differential microphone preamp, pin 2 hot. Input impedance: 4 kOhms differential. Input level, min gain: 0 dBFS is obtained with a +9 dBu signal at the XLR input.
Input level, max gain: 0 dBFS is obtained with a -44 dBu signal at the XLR input. Frequency response: From 7 Hz to 32 kHz within 0.5 dB (96 kHz sample rate). Dynamic Range: 116 dB(A). THD+N: -104 dB(A) at -10 dBFS.
Configuration: Class-A discrete differential line receiver, tip hot. Input impedance: 20 kOhms differential. Input level, min gain: 0 dBFS is obtained with a +26 dBu signal at the TRS input. Input level, max gain: 0 dBFS is obtained with a -27 dBu signal at the TRS input. THD+N: -104 dB(A) at -10 Dbfs.
One 1/4 instrument input jacks. Two analog potentiometers for Input GAIN. Two 5 segments input level meter (peak). Analog potentiometers for Z-Tone control.Master potentiometer for main output control. MIDI I/O 5-pin DIN connectors. B-Type USB socket for connecting a computer (Mac/PC). 2 x 1/4 TRS External controllers sockets. 2 x 1/4 TRS Balanced floating line outputs.
1 Combo socket for MIC input and Line input (auto selecting). USB A-Type to USB B-Type connection cable (1.5m/4.32ft). Size: 19.5cm x 19.5cm x 5.3cm. Requires a 64 bit CPU and Operating System. MacOS 10.11 or later.
And other US Territories having a valid United States Postal Service Zip Code. All major credit cards are accepted. We are not responsible for any damage caused by not adhering to the voltage requirements. The item "IK Multimedia AXE I/O SOLO 2x3 USB Guitar Audio/MIDI Interface" is in sale since Sunday, October 18, 2020.
This item is in the category "Musical Instruments & Gear\Pro Audio Equipment\Audio/MIDI Interfaces". The seller is "yejeysound" and is located in Miami, Florida. This item can be shipped to United States, Canada, United Kingdom, Denmark, Romania, Slovakia, Bulgaria, Czech republic, Finland, Hungary, Latvia, Lithuania, Malta, Estonia, Australia, Greece, Portugal, Cyprus, Slovenia, Japan, China, Sweden, South Korea, Indonesia, Taiwan, South africa, Thailand, Belgium, France, Hong Kong, Ireland, Netherlands, Poland, Spain, Italy, Germany, Austria, Bahamas, Israel, Mexico, New Zealand, Philippines, Singapore, Switzerland, Norway, Saudi arabia, Ukraine, United arab emirates, Qatar, Kuwait, Bahrain, Croatia, Malaysia, Brazil, Chile, Colombia, Costa rica, Panama, Trinidad and tobago, Antigua and barbuda, Aruba, Belize, Dominica, Grenada, Saint kitts and nevis, Saint lucia, Montserrat, Turks and caicos islands, Barbados, Bangladesh, Bermuda, Brunei darussalam, Bolivia, Ecuador, Egypt, French guiana, Guernsey, Gibraltar, Guadeloupe, Iceland, Jersey, Jordan, Cambodia, Cayman islands, Liechtenstein, Sri lanka, Luxembourg, Monaco, Macao, Martinique, Maldives, Nicaragua, Oman, Peru, Pakistan, Paraguay, Reunion, Viet nam, Uruguay. Number of Channels: 2